|
Blend, Chop & Mix
Coffee & Espresso
Grills, Fryers & Cookers
Toasters & Ovens
Juicers & Drink Makers
|
|
|
|
KitchenAid K45B Flat Beater Replacement for KSM90 and K45 Stand Mixer | 
 enlarge | Brand: KitchenAid
List Price: $14.99
Buy New: $11.99
You Save: $3.00 (20%)
Rating:  36 reviews
Shipping Weight (lbs): 0.5
Dimensions (in): 7.3 x 4.7 x 4.5
Warranty: 1
MPN: K45B
Model: K45B
UPC: 050946000626
EAN: 0050946000626
ASIN: B00005LD47
Availability: Usually ships in 24 hours
| |
| Features:
| • | Replacement nylon-coated flat beater | | • | Use with KitchenAid KSM90 and K45 stand mixers | | • | Perfect for mixing cake batter, cookie dough, and more | | • | Handwash only | | • | Measures approximately 7-1/2 by 4-1/2 by 4-3/4 inches; 1-year warranty |
|
| Similar Items:
|
| Editorial Reviews:
Product Description
Mix up your favorite desserts with KitchenAid's flat beater. This nylon-coated attachment fits 4-1/2-quart KitchenAid stand mixers. The beater is perfect for mashing potatoes, mixing cake batter and cookie dough, and so much more.
|
| Customer Reviews: Read 5 more reviews...
 Adjust your beater to bowl clearance to eliminate chipping November 25, 2008
Momof 3 (Michigan)
1 out of 1 found this review helpful
After reading these reviews, it is apparent that many people do not check their beater to bowl clearance. If a beater is chipping on the bottom, it means that it is too low. You can look in your use and care guide, or go to kitchenaid.com to watch a video on how to locate the adjustment screw. If the mixer doesn't incorporate the ingredients in the bottom of the bowl, then the beater is too far away from the bowl. If you have a tilt-head mixer, the adjustment screw is located in the neck of the mixer-in the hinge-when you lift up the head, you'll see it. You can place a dime in the bottom of the bowl, and turn the mixer to "stir". If the dime moves around continuously, it is too low. If it doesn't move at all, it is too high and can't reach everything. It should scoot the dime around the bowl 1/4-1/2" at a time. I've had my beater, which is used a lot, for about 5 years, and it has no chips. If you have a bowl lift mixer, the adjustment screw is behind the bowl clip. If it's adjusted properly, you get the best mixing and the least wear and tear on your beater and bowl. The adjustment can change slightly over time.
Don't put in dishwasher November 23, 2008
Kathleen Neumann
This is the third of these I've had to buy. Certainly the KitchenAid does a wonderful job but I wish they would make these out of stainless like their other beater. The white coating chips and peals and falls into the food. Apparently it is because I've been putting it in the dishwasher. However, as far as ordering from Amazon goes, the beater arrived quickly and in perfect condition. I gave it four stars because it does a good job but it does not last as long as you would expect a KitchenAid product to last.
K45 Beater October 21, 2008
F. Bain
This beater is working well. Our old one had lost the white covering, exposing the aluminum so it had to go. The coating on this one appears to be solid.
A fine replacement October 18, 2008
Alison A. (Phila, PA USA)
I have owned my 4.5 qt Kitchen Aid Stand Mixer for 15+ years and have had excellent results. The beater is the only part that ever needed to be replaced and it was our fault. Someone (no one admits to the crime) placed the beater in the dishwasher next to a very sharp Henkel knife that sliced into its white coating. Once sliced, the coating peeled. So I finally broke down and replaced the beater attachment. I made pastry crust and biscuits the first day and my husband was thrilled to have the Mixer back in working order.
Quality Merchandise July 24, 2008
KAE D (California)
I especially like this beater because I can clean batter off more easily with a spatuala because it is so open.
|
|
|
|
| |
